specification of error
英 [ˌspesɪfɪˈkeɪʃn ɒv ˈerə(r)]
美 [ˌspesɪfɪˈkeɪʃn əv ˈerər]
【计】出错说明， 出错描述
双语例句
- The Optim solutions support an iterative testing model that simplifies specification of error and boundary conditions and simplifies the comparison of test results to baseline data.
Optim解决方案支持迭代测试模型，该模型简化了错误和限制条件说明，以及测试结果与基线数据的对比。 - It shows how to check various combinations of SSL Cipher Specification ( SSLCIPH). It also demonstrates error scenarios like invalid certificates and expired certificates.
本教程还将展示如何检查SSLCipherSpecification（SSLCIPH）的各种组合，以及诸如无效证书和过期证书之类的错误场景。 - Unless otherwise specified, failure to observe a prescription of this specification indicated by one of the keywords must, required, must not, shall and shall not is an error.
除非另有规定，如果不能遵守“一定、必需、绝不是，应该，不应该”这些关键词标明的规范的规定，那么算作一个错误。 - A precise specification of the item, such as a property name, that caused the error.
导致错误的项的精确说明，例如属性名。 - Based on the Bluetooth specification 1. 1, the thesis studies the details of the algorithms of the base band specifications, and designs blocks of error correction, error detection, data whitening, hop selection kernel and Bluetooth security which include encryption and authentication.
文章以蓝牙规范1.1为标准，详细分析了蓝牙基带协议栈的具体内容，在此基础上，对基带数据处理部分的纠错、检错、扰码、蓝牙时钟、接收相关器等进行了设计； - Taking a circular aperture exponential distribution as an example, the radiation specification of different test distances is calculated, thus the effect of measurement distance on antenna pattern sidelobe specification is investigated. The relationship curve of the first sidelobe measurement error versus measurement distance is given.
以圆口径指数型分布为例，计算了在不同测量距离下的辐射特性，从而研究了测量距离对天线方向图旁瓣特性的影响，给出了第一旁瓣测量误差与测量距离的关系曲线。 - The specification of random error term is a complex problem in econometric modeling.
困扰计量经济建模的一个重要问题是模型中随机扰动项性质的设定。 - According to the performance specification of the H ∞ torsional modal observer, a bound of the maximum energy gain between the estimation error and the residual modes is introduced to attenuate the effect of the residual modes.
通过分析H∞扭振模态观测器的性能指标可知，H∞扭振模态观测器引入了一个反映受控模态估计偏差对剩余模态分量的最大能量增益的约束，以抑制剩余模态分量的影响。 - In addition, the demanding technical specification is still indispensable factor, which accords with the special bandwidth demand of the grid drive pulse in measuring the convergence error.
此外，为符合会聚误差测量中栅极驱动脉冲特定带宽的要求，脉冲的高技术指标仍然是不可缺少的因数。 - After analyzing CAN protocol specification, the node-centric state machine models of sender and receiver are built respectively. As a supplement for the model, the error count state machine models are established.
对于CAN总线，从节点中心的角度，建立了节点的发送和接收状态机模型，以及各自补充的错误计数状态机模型。 - Since the transformation of the old road plane fitting precision linear specification is not clear, In this paper, made to the accuracy of 0.1 meters as the tolerance of the special sections and large sections of the measurement error due to relax the accuracy requirements.
由于现阶段对旧路改造平面线形拟合精度没有明确规范要求，本文提出以0.1m作为精度限差，对特殊路段和测量误差较大的路段可适当放宽精度要求。 - B is established on Zermelo-Frankel set theory. It expresses states transferring by signal method. So both program and its specification are on uniform framework, which can reduce the possibility of semantic error.
B建立在Zermelo-Frankel集合理论的基础上，它使用符号表示法（广义代换）来表达状态的转换，使程序及其规格说明处于统一的数学框架之下，减少了出现语义错误的可能性。 - According to the same principle, the generation methods of prismatic and spherical specification surface model are also put forward. Secondly, the operator of perpendicularity error evaluation of an axis is designed.
根据相同的原理也提出了棱柱体和球的规范表面模型的生成方法。第二，设计了获取圆柱轴线以及轴线对端面垂直度的操作算子。